|
|
Ford Replacement
Harnesses
You have reached The Detail Zone, the premier manufacturer
of stand-alone GM and Ford fuel injection wiring systems. We are pleased to offer complete sections of replacement
harnesses found to be troublesome in Ford production vehicles. You
will find that most of these harnesses are no longer available from the
factory. All of our harnesses are manufactured with factory correct
connectors and terminals using high grade crosslink automotive grade wire.
Factory dimensioned for easy, trouble free installation. We also offer some vehicle specify fuel injection harnesses
for various applications. See the bottom of the page for info about custom work. Order online, call us toll free at 877-968-7842 or check
with your favorite Mustang Shop. Print / Download our Ford
Parts Flyer (You'll need Adobe Acrobat) DEALER INQUIRIES WELCOME
FORD 2.3 TURBO ENGINE SWAP HARNESS
Based on the 1987-88 Turbo Coupe ECM, this harness is
designed for swapping a 2.3 Turbo into other late model Fords (though it's a
good replacement for factory equipped 2.3 Turbo vehicles as well). Harness
has 48 inches between ECM and back of engine. Engine harness is
complete with circuits for electric fans, fuel pump, diagnostic port, water
temp/oil press and alternator. Comes with enough hi temp zip loom and
harness wrap tape to complete once lengths and layout is verified. System
also includes a firewall grommet and complete instructions.
FORD TURBO COUPE INJECTOR HARNESS (1987-1988) This harness sits on top of the motor and connects the injectors and other engine sensors to the main harness. Built to factory specs and dimensions using all new Ford parts.
This section of harness connects the two oxygen sensors and oil level sensor into the main harness. Please note the oxygen sensor connectors in the picture and match them to what you need. Fits both auto and manual transmissions.
This section of harness connects the two oxygen sensors and oil level sensor into the main harness. Note that there is an automatic and manual transmission version.
EXTENDED MUSTANG OXYGEN SENSOR HARNESSES Kill two birds with one stone. Same as Mustang Oxygen Sensor Harnesses above but with an additional 24 inches built into the harness to accommodate long tube headers. Eliminate the need to add extensions later.
Other New Products for Fords
These
24 inch harness extensions allow oxygen sensor relocation when using long
tube headers. Our extensions are year specific so that you do not have to
modify the connectors on the oxygen sensors. Totally plug and play. No
modifications necessary.
Replacement grommet for many fuel injected Fords. Fits factory firewall hole
for the injection harness. Hole size is 1.25 inches, panel hole size is 3
inches by 1.5 inches.
Convert
from late model EV6 injectors to early EV1 injectors without cutting into
the factory harness. Plugs in between the factory harness and an EV1 (D
Style) Injector. Built right with quality parts from the correct
manufacturers. Quality checked for guaranteed performance.
Necessary when swapping to a Cobra Mass Air Flow Meter or relocating the IAT
Sensor. Factory terminated with 18 inch wire leads.
Necessary when swapping or relocating the Mass Air Flow Meter. Connector has
6 positions but only 4 are used as on 1996 - 2004 Ford Mustangs. Factory
terminated with 36 inch wire leads.
MASS AIR FLOW EXTENSION (2005 and Newer)
Necessary when swapping or relocating the Mass Air Flow Meter. Connector has
6 positions as on 2005 - Up Ford Mustangs. Factory
terminated with 36 inch wire leads.
FORD 5.0 EFI WIRING SYSTEM FOR DIRECT FIT TO 1965-1970 FORD MUSTANGS & 1966-1977 FORD BRONCOS.
Available at the following outlets or check with your local Mustang / Bronco retailer:
FORD 5.0 EFI UNIVERSAL SYSTEM
Available at the following outlets or check with your local Mustang / Bronco retailer:
BRONCO HEADLIGHT HARNESS
Get brighter headlights in your early Bronco! The unique relay system takes the load off the headlight switch and delivers battery power directly to the headlights. More voltage equals brighter lights. Simple installation. Comes with everything necessary for installation including complete instructions.
Available at the following outlets or check with your local Mustang / Bronco retailer:
CUSTOM JOBS QUOTED - LARGE AND SMALL
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Copyright © 2004 The Detail
Zone |
We
are pleased to introduce this stand alone Ford fuel injection harness sized
exclusively for both early Mustangs and Broncos. Designed with RJM
Technology, this kit is a direct fit and is finished off with hi temp zip
loom and harness wrap tape. Works with mass air flow equipped 302 and 351
engines. System includes a firewall grommet and complete instructions.
This
stand alone Ford fuel injection harness is sized to fit Cobra Replicas but
can be used in most universal installs where the ECM is placed behind the
dash. Designed with RJM Technology, this kit is semi finished off and comes
with enough hi temp zip loom and harness wrap tape to complete once lengths
and layout is verified.. Works with mass air flow equipped 302 and 351
engines. System also includes a firewall grommet and complete instructions.
